Manufacturers
Payments Accepted
BOX_INFORMATION_CARD
BOX_INFORMATION_CARD
Trade Associations

C6 Performance is a Proud Member of SEMAProud Member of The National Corvette Museum

Radiator Shroud, Lower Support, 2010-2013 C6 ZR1 Corvette, w/o Perf Pkg, GM OEM Part  Product 180 of 181 in category Air Intakes C6, Z06, Grand Sport, ZR1  Halltech 4.5" X 4.00" Stock C6 Throttle Body Connector Hose to Super Bee Air Bridge

Halltech Killer Bee II CF112 Package C6 Corvette 2006-2013 Z06, and LS3 Corvette, No Beehive

Halltech Killer Bee II CF112 Package C6 Corvette 2006-2013 Z06, and LS3 Corvette, No Beehive

$849.00 

Add to Wish List

Halltech Killer Bee II CF112 Package C6 Corvette 2006-2013 Z06, and LS3 Corvette, No Beehive Included.

NOTE: Carbon Fiber Behhive shown in images is not be included. Carbon Fiber Behive CF112 version is Part Number: BEELINE

Our first independent dyno numbers are just in.  Dynoed on a brand new 2010 Z06 just off the trailer:  Stock 448.9RWHP/431.6 lb-ft  Halltech Killer Bee™II CF112 installed 10 minutes later:  481.9 RWHP/449.1 lb-ft. Tq.  91 Octane pump gas, reprogrammed MAF tables to set new long term fuel trims, but other than 2 degrees additional timing, the factory programming was stock.  Next: 3-08-10 Katech Engine Development dynoed 618 HP vs. 604 with the GM stock intake on their Superflow Engine Dyno.  +14 HP.  Halltech's all new designed Killer Bee™ II CF112 designed to compliment the Williams Performance 102mm Throttle Body and FAST LSXR 102 intake manifold. Recalibration of the MAF tables is required for maximum performance.  The optional Halltech Super Beehive™ Carbon Fiber Heat Shield should be ordered for heat shielding of the filter. Halltech's MAF relocation wire harness included in pricing.  Halltech's Filters have been tested using ISO 5011 standards and now have 109g of extra dust capacity.  This system will be the exclusive induction system used by Katech on all of their Track Attack engine builds.  Custom programming is available through Halltech's exclusive e-mailtune®, with the SCT X3 Hand Held tuners available soon with pre-populated programming developed on the dyno.
 
Fits all Corvettes 2008 and above as well as all C6/Z06 2006 and above!

    * +33 RWHP/26 lb-ft Tq. with recalibration of MAF tables only on 91 Octane Fuel vs. stock (Test Vehicle 2010 Z06 with 10 miles, just off the carrier)
    * +14 HP on the Katech Superflow Engine dyno over GM stock LS7 intake
    * Mass Air Flow Sensor relocation under the Super Beehive™ Heat Shield/Radiator Bezel
    * Zero Obstruction to flow at the throttle body
    * 112mm outlet to match the new Billet WP 102mm Throttle Body and FAST intake manifold
    * 112.5mm inlet from the all new Killer Bee II filter
    * Relocation of the Dry Sump vent tube to the filter bottom
    * Larger plenum and redesigned flow design by Jim Hall
    * Built in Velocity Stack Bellmouth filter flange
    * More Horsepower and torque than any other intake made for the Corvette
    * Pure Carbon Fiber made by the company that makes Pratt & Miller C6.RS body panels
    * MAF relocation wire harness included
    * May Require PCM Tuning for Maximum Horsepower!

The Halltech CF112 comes with our carbon fiber intake, connector hose, hose clamps and Super Flow filter. No Beehive with this package. If you need the Beehive, please note that in comments and we will debit your card $99.00 for the plastic version. For the full carbon fiber Beeline, check out that product. Fits the Carbon Edition too.

Please Specifiy if you have stock or Nick Williams 102 MM Throttle Body.

This product was added to our catalog on Thursday 30 January, 2020.
Points & Rewards Information
Points Credit : 849 points Currently valued at $25.47
Write a Review and earn $1.5 worth of points.
Please check the Reward Point Program FAQ for more information.
Radiator Shroud, Lower Support, 2010-2013 C6 ZR1 Corvette, w/o Perf Pkg, GM OEM Part  Product 180 of 181 in category Air Intakes C6, Z06, Grand Sport, ZR1  Halltech 4.5" X 4.00" Stock C6 Throttle Body Connector Hose to Super Bee Air Bridge
Manufacturers
Payments Accepted
BOX_INFORMATION_CARD
BOX_INFORMATION_CARD
Trade Associations

C6 Performance is a Proud Member of SEMAProud Member of The National Corvette Museum

  • Shopping Cart
  • 0 items
My Account Info
Live Support
Social Networking


Check us out on Facebook!

Follow us on Twitter!
See our Videos on YouTube!

Check out our eBay Store!

Secure Payment
Process Credit Cards


This Website is 100% secured!
Transactions on this site are protected with up to 256-bit Secure Sockets Layer (SSL) encryption.

Win with C6 Performance, the Best place for quality C8, C7, C6, C5 Grand Sport, ZR1 and Z06 Corvette and Camaro Parts
WARNING: Cancer and Reproductive Harm - www.P65warnings.ca.gov WARNING: Cancer and Reproductive Harm - www.P65warnings.ca.gov
All Content COPYRIGHT 2000-2020 C6 Performance and Loaded Commerce. All Rights Reserved.